GO-1026MG (0.11s/60°, 11kg.cm)

Product no.: KAV20.1026MG

can be shipped within 3-14 days


Price incl. VAT, plus Shipping

Extra strong thin (10mm) programmable digital micro servo 26g with metal gear and supply voltage range 6.0-8.4V, 2xBB, ideal for ailerons and flaps of gliders. Positioning force 8.2kg.cm, speed 0.15s/60° at 6.0V, positioning force 10kg.cm, speed 0.12s/60° at 7.4V. Aluminum housing for perfect cooling under high loads.
Extra strong, programmable digital micro servo with steel gears and output shaft with two ball bearings is intended for use in all types of RC models. Thanks to the flat housing with a height of 10 mm, it is particularly suitable for controlling ailerons and flaps in RC glider models with thin wing profiles. The servo is placed in an aluminum housing that ensures perfect cooling even under high loads.

With the USB programmer/interface for GO Servos and the PC operating program you can program a large number of servo parameters (travel size, travel neutral, overload protection, soft start, fail-safe etc.).

Programmable features

Deflection Size: Used to set the maximum size of the servo deflections. The default setting is about 120° with the normal range of control pulse widths (900~2100 µs); Approx. 180° at the maximum permissible range of control pulse widths (500~2500 µs).
Servo neutral position: Used to adjust the neutral position (middle position) of the servo.
Damping: Adjusts the characteristics of the servo's behavior when stopping its movement.
Output Power: Sets the output power of the servo. The higher the value, the faster the servo and the higher the force - of course, the power consumption is proportionally higher. Range: 39.2~100%
Sensitivity: Adjusts the sensitivity (deadband) of the servo. The higher the value, the narrower the deadband - the servo will only move if the change in control signal width is greater than the deadband. If you set the sensitivity value too high, the servo may oscillate in some applications. Range: Ultra High (Extra high - dead band approx. 1 µs) - High (High - approx. 2 µs) - Medium (Medium - approx. 3 µs) - Low (Low - approx. 4 µs)
Soft start: Turns on/off the soft start function. This feature prevents the servo from going to the operating position abruptly after connecting the power supply, thus reducing the risk of damaging its gearing.
Servo Reverse: Reverses the servo deflections.
FUTABA SR mode: Only for use with channels of RC sets FUTABA that work in SR mode. Do not turn on this option if you are using another FUTABA RC set setup or another brand RC set.
SANWA SSR mode: Only for use with channels of RC sets SANWA that work in SSR mode. Do not turn on this option if you are using a different setup of the SANWA RC set or a different brand of RC set.
Fail-safe: If the receiver's control signal fails completely or the servo cannot detect the signal correctly (e.g. due to interference), the servo can switch to one of three emergency modes:
(a) Free: Fail-safe is switched off.
(b) Hold Position: The servo will hold the position corresponding to the last correctly received signal.
(c) Transition to the neutral position: The servo returns to the neutral position (pulse width 1500 µs).
Overload Protection: Enables or disables three levels of servo overload protection - once the overload lasts for a preset time (in seconds), the servo output power is limited to the corresponding preset value (in % of maximum power).
Reset: Restores the factory settings of the connected servo.
Increased supply voltage 6.0-7.4 V (nominal voltage).

Output shaft with 25-tooth thousand edge.

Servo size Micro
Servo type digital
Actuating force with 6.0V [kg/cm] 8.2
Actuating force with 7.4V [kg/cm] 10
Actuating force with 8.4V [kg/cm] 11
Speed at 6.0V [s/60st.] 0.15
Speed at 7.4V [s/60st.] 0.12
Speed at 8.4V [s/60st.] 0.11
Servo gear metal
Ball bearing 2×
High voltage yes
Power supply [V] 6 - 8.4
Length [mm] 29
Width [mm] 10
Height [mm] 30.5
Weight [g] 26
Intended for airplanes

Browse this category: Servos